Upright Frames
Each frame is smoothly punched throughout its entire length in two inch increments on M-I & Teardrop (three inch increments on Slotted) for fast, inexpensive installation and adjustment.

There are two basic column sizes, each available in three gauges on M-I and Teardrop (two gauges on Slotted) to accomodate your specific loading requirements.

All columns are roll-formed using 50,000 psi minimum yield steel. They are designed to meet RMI specifications and have a minimum safety factor of 1.92 to 1.

Horizontal and diagonal braces act as both compression and tension member for increased strength.

Formed Beams
Each beam is a roll-formed single piece of High Strength steel with a continuous seam weld.

Inca's positive locking device prevents accidental dislodging of beam, yet allows for easy adjustments.

INCA's beam safety factor of 1.65 to 1 conforms with current Rack Manufactures' Institute standards.

Capacities range from 3,000 to 6,000 pounds.

is a carefully engineered system designed to provide highly efficient storage of palletized items. Excellent design features combined with the use of high strength steel produces a superior pallet rack that can handle nearly any job you can give it. Following is a list of the wide range of features and components that make Penco Rack one of the best values for your storage dollar.

DESIGN FEATURES

The basic components of Penco Pallet Rack are Upright Frames and Beams. Each is manufactured to exacting tolerances to provide many years of dependable service at their rated loads.

PALLET RACK BEAMS

Penco has engineered its roll-formed one piece beam to achieve the highest possible strength-to-weight ratios in the most frequently desired load ratings through the use of efficient design and high strength steel.

Beams are offered in different vertical profiles and steel gauges. Beam step heights of 7/8" and 1-5/8" are available for a wide variety of accessory use. Both the overlapping seam and the beam end connector are securely MIG welded for strength.

The face of the beam has an M-design recessed configuration for added strength, protecting the locking key, and to accept pressure sensitive labeling. Each beam is stamped with an identifying letter referring to the load bearing capacity. Beams are finished in 710 Safety Yellow baked enamel for high visibility.

Penco Pallet Rack Upright Frames are available in five load capacities, ranging from 18,000 lbs. to 45,000 lbs. A letter code stamped into the face of the post indicates the capacity. Depths of 30", 36", 42", 48", 54" and 60" are standard, but other depths areavailable. Standard heights range from 48" to 288" in 6" increments, but greater heights can be achieved when splices are used.

Beam heights adjust on 3" vertical centers, and are independent on each side of the frame. Beams of any type can be placed along the full height of the post; there are no dead spots on the post, even across a splice. Various load rated frames can be combined in a row of rack for maximum economy.

Penco Pallet Rack Upright Frames are furnished completely fabricated, welded into rigid units. Standard finish for upright frames is 028 Gray baked enamel.

We recommend that all upright frames be securely anchored to the floor for safety.

PALLET RACK ACCESSORIES

PLYWOOD SUPPORTS:
For supporting plywood or other wood decking. Styles are available for 1/2" deck on 7/8" step beams and 3/4" deck on 1-5/8" step beams.

GENERAL DUTY CROSS BARS:
For supporting loads smaller than unit depth.

HEAVY DUTY FLANGED CROSS BAR:
Supports heavier loads smaller than unit depth on 1-5/8" step beams.

FORK CLEARANCE BAR:
Provides proper fork clearance for unpalletized stock, 2" wide by 2-3/4" high.

HEAVY DUTY SKID CHANNEL ASSEMBLY:
Provides a channeled base for skid runners, 4" wide by 2" high.

FRAME SPLICE:
For adding to height of existing frame. Can be supplied welded in top of new frame if specified on order. (Top frame must be ordered without foot plate.) With hardware.

FRAME PROTECTOR:
Anchors to floor at front of post. Provides protection against damage from material handling vehicles.

RIGID WALL BRACKET:
Structurally connects racks to wall for additional stability. Frame hardware included.

RIGID ROW SPACER:
Structurally connects and spaces two rows of rack back-to-back. Bolted type. Hardware included.

REEL HOLDER:
Accessorizes rack for reel storage. Max. axle 2-1/2" diameter.